Lire cet article en français : Home Assistant Connect AUX-2 : le nouveau multi-outil domotique de Nabu Casa
Nabu Casa, the company behind Home Assistant, put out a new piece of hardware on November 11, 2026: the Home Assistant Connect AUX-2. Nabu Casa calls it “a smart home multi-tool,” which is a more honest label than “hub” or “gateway.” It isn’t meant to replace your existing Home Assistant setup. It’s an expansion board that adds a handful of useful ports and radios to a system you already run, so you can reach corners of your smart home that a typical hub just doesn’t cover.
What the AUX-2 actually does
For such a small box, it packs in a lot. On the audio side, there’s a combined optical (S/PDIF) and 3.5mm analog output, built around a TI PCM5122 DAC rated at 112dB SNR, handling 24-bit/48kHz stereo. It’s built to pair with Music Assistant and the Sendspin protocol, and it plays FLAC, MP3, and WAV files. There’s no audio input and no Bluetooth audio here, so this is strictly for pushing sound out to a stereo or amplifier elsewhere in the house.
If you’re still dealing with older or industrial gear, the AUX-2 has two RS-232 serial ports through 3.5mm connectors, each with a TX/RX swap switch so you don’t have to go hunting for a null-modem cable. Modbus RS-485 is also an option, though you’ll need a separate USB adapter (around $15) that doesn’t come in the box.
There’s a USB-A port too, and it can host a Home Assistant Connect ZWA-2 Z-Wave stick remotely. That’s a nice detail if you want to hide the AUX-2 itself out of view while still giving the Z-Wave antenna a clear line of sight. Add to that a Bluetooth 5 LE proxy with its own dedicated antenna, a Grove port for GPIO and I2C sensors, and Wi-Fi limited to 2.4GHz.
Power comes from either PoE (802.3af) or USB-C (5V/2A or more). You get one or the other, not both.
Zigbee works, but read the fine print
Zigbee is supported, but only through Home Assistant’s built-in ZHA integration, not Zigbee2MQTT. For readers of this site, that’s worth sitting with for a second: plenty of self-hosters picked Zigbee2MQTT specifically for the flexibility it gives over ZHA, something we go into in our Zigbee2MQTT review. If your Zigbee setup already runs on Zigbee2MQTT and a separate MQTT broker, the AUX-2’s radio doesn’t just drop in. You’d be committing to ZHA for this specific device.
It’s also worth setting expectations here. Zigbee requires Home Assistant 2026.11 or later, and Nabu Casa’s own FAQ calls it “not widely tested” at launch. That’s not a dealbreaker, but it’s a reasonable thing to know before building a Zigbee network around this device on day one.
And Thread isn’t part of the picture at all, and apparently never will be. Nabu Casa says Thread support “isn’t planned.” If that matters to you, this isn’t the device.
An open-hardware gesture worth noting
The more interesting part of this launch, at least for a self-hosting crowd, is what’s inside rather than what’s on the outside. The AUX-2 runs on an ESP32-S3 SoC with ESPHome-based firmware and an unlocked bootloader, so it isn’t sealed off from tinkering the way most consumer smart home gear is. Nabu Casa says it plans to release the PCB design files and the 3D-print files for the enclosure. That’s a real open-hardware move, and one that fits the project’s general ethos. The case opens with four Phillips screws, no glue, no clips, so taking it apart to fix or modify something doesn’t mean fighting the hardware first.
What you need to set it up
You’ll need Home Assistant 2026.9 or later just to get the AUX-2 running, and 2026.11 or later if you want its Zigbee radio to work at all. Our recent piece on the Home Assistant 2026.11 release covers what changed in that update. Setup goes through the ESPHome integration, which will feel familiar if you’ve set up other ESPHome devices before.
As for the hardware itself: 106 × 63 × 25mm, 104 grams, indoor use only, and an operating range of 0 to 65°C. Not something you’d want bolted to an outside wall or left in an unheated garage.
Price and where to get one
Nabu Casa priced it at $69 in the US and €59 in Europe. The US figure excludes tax, the European one includes it, and actual prices will shift a bit depending on region and retailer. It went on sale worldwide on November 11, 2026, through Ameridroid, CloudFree, and Apollo Automation, all US-based, with Apollo Automation also shipping to Canada. Cables aren’t included, so factor that in. Nabu Casa’s own product page still carries a “New product! Stock may be limited” notice, which is worth keeping in mind if you’re thinking about ordering one soon.
For the full spec sheet, and the reasoning behind some of the choices here, Nabu Casa’s own announcement is a good read: the “No device left behind” blog post and the AUX-2 product page both go deeper on specific use cases than this article can.
The bottom line
The AUX-2 is a niche product, and it seems designed that way on purpose. It’s not a new Home Assistant hub, and it won’t replace a dedicated Zigbee coordinator for anyone already committed to Zigbee2MQTT. What it does bring is an unusual mix: legacy serial ports, a genuinely solid DAC for whole-home audio through Music Assistant, Bluetooth proxying, and a remote Z-Wave USB host, all built on hardware Nabu Casa says it intends to keep open. If you’ve been cobbling together old serial-connected equipment, or just want a cleaner way to add audio output to a Home Assistant setup, this fills a gap that most general-purpose hubs leave alone.
